Table Of Content
Monel 400/500 Fasteners. The copper and nickel alloy used to make Monel 400/K500 Fasteners has great strength and excellent corrosion resistance. Furthermore, it has a high degree of stability and toughness and is well-resistant to hydraulic acid and seawater. Incredible hardness and resistivity are its alloy’s most remarkable characteristics.
The copper and nickel alloy used to make Monel 400/K500 Fasteners has great strength and excellent corrosion resistance. Furthermore, it has a high degree of stability and toughness and is well-resistant to hydraulic acid and seawater. Incredible hardness and resistivity are its alloy’s most remarkable characteristics. This alloy is trusted for use because of its specialization with DIN, ASTM, SAE, and ASME, as well as a few other factors. Due to all of these characteristics, they are low efficiency and non-magnetic at temperatures as low as -150 degrees Celsius.
Monel 400 Fasteners are widely selected for their strength, temperature, and pressure sustainability. It also extended its uses in corrosive applications such as the food and chemical industry. These are flexible to form and easily adaptable in any system. The correct fasteners are easy to install and remove. Monel 400 provides immense strength against stress-cracking corrosion caused during severe temperatures. In the manufacture heat exchangers, valves, pumps, and hydrocarbon and chemical processing equipment, 400 Fasteners are used.
Monel 500 Fasteners are implemented by adding the increased value of iron; thus, it progresses characteristic of strength and resistance to corrosion and heat. We offer these fasteners with rust-free and pitless surfaces. These grade fasteners are highly opposed to decomposition in seawater and the chlorine ion effect. It is utilized in the power and pharmaceutical industry with pulp, paper, and refineries. It has been discovered that k500 Fasteners can withstand a sour-gas atmosphere. Seawater moving at high speed exhibits very little corrosion while preserving its high strength.
|Standard||ASTM F467 / ASME SF 467|
|Bolt / Screw Size||M3 – M56 | 3/6″ to 2″ | Custom Sizes|
|Nuts Size||M3 – M56 | 3/6″ to 2″ | Custom Sizes|
|Washers Size||M3 – M56 | 3/6″ to 2″ | Custom Sizes|
|Machine Screws Size||M1.6 – M12|
|Self Tapping Screw Size||No.2 – No. 14|
|Length||3 mm to 200 mm|
|Studs, Bolts, Threads||UNF, BSW, BSF, METRIC, UNC, or as required|
|Threads Configuration||ASME B1.1 2A/3A – 2B/3B Inch Unified Threads and B1.13M 6h-6G Metric Coarse Threads|
|Certification||Dual Certified As per ASTM & ASME Codes|
|Dimensions||DIN 931, 933, 934, 7991, 976, 125, ASME B18.2.1, B18.3|
|Threads||Unless otherwise specified, the threads shall be rolled or cut and tapped horizontally or vertically|
|Test Certificate of Bolting||as per EN 10204 / 3.1 Manufacturer Test Certificate|
|Monel K500||0.25 max||1.5 max||0.5 max||0.010 max||27.00 – 33.00||0.5 – 2||63.00 min|
|Element||Density||Melting Point||Tensile Strength||Yield Strength (0.2%Offset)||Elongation|
|Monel K500||8.44 g/cm3||1350 °C (2460 °F)||Psi – 160000 , MPa – 1100||Psi – 115000 , MPa – 790||20 %|